Faucet & Fixture Installation in St. Louis, Missouri

A compression faucet (two-handle, rubber-seat style) with a drip is a manageable DIY repair if the supply valve shuts off fully — replace the seat washer and O-ring. Cartridge and ceramic-disc faucets require identifying the cartridge by disassembling the handle, which is possible with patience. When a plumber is warranted: the supply valve under the sink won't close completely (corroded or stuck), the faucet body is cracked, the wall stop valve needs replacement, or you're changing the number of supply connections (single-handle to double-handle, for example). Any of these requires a licensed plumber.

Replacing a faucet at an existing supply connection (same location, same number of holes) does not require a permit in most jurisdictions. Rough-in changes do require a permit: relocating a supply connection, adding a new fixture location, installing an outdoor hose bib with a buried line, or adding a new bathroom or kitchen sink where there wasn't one before. The plumber confirms permit requirements as part of the scope review and pulls the permit when the work requires it.

A pressure-balance (P-B) valve maintains a consistent hot/cold ratio when pressure changes elsewhere in the system — like when someone flushes a toilet while you're in the shower. Without one, a sudden drop in cold pressure from a toilet flush can momentarily swing the shower mix to near-full-hot, causing a scald. Most state plumbing codes require P-B valves in all new shower and tub/shower installations; replacement of older tub-only faucets is a code-compliant upgrade opportunity. If your shower produces brief temperature spikes, the existing valve likely lacks pressure balance.

Before buying: count the mounting holes in the sink deck (1-hole, 3-hole, and 4-hole are the common configurations — these are not interchangeable without a deck plate or new sink). Measure the supply tube size under the current faucet (⅜-inch OD compression fitting is standard; older homes may have ½-inch IPS). Check the deck thickness — thick granite or engineered stone countertops often require extended-reach shanks that not all faucets include. Confirming these details before purchase saves the plumber a materials run and keeps the installation on-schedule.

A straightforward kitchen or bathroom faucet swap at an existing connection takes 1–2 hours, including shutoff valve inspection, connection testing, and aerator flushing (to clear any installation debris). A bathtub or shower valve requires accessing the valve body through the wall — add 2–3 hours plus drywall access-panel installation or patching. Outdoor hose bib replacement takes 1–2 hours, or longer if the existing bib lacks a proper shutoff and one needs to be added. All these timelines assume the shutoff valves function — corroded valves that need replacement add 30–60 minutes per valve.

St. Louis water hardness of 8 gpg is in the hard range, where scale builds up quickly inside water heaters, tankless units, and pipes. A whole-home water softener pays for itself through extended appliance life in this hardness range. Tankless water heaters in this market need descaling every 18–24 months to maintain warranty compliance and efficiency.

St. Louis has a documented lead service line inventory (Unknown). Faucet replacement in a home with lead service lines should use NSF/ANSI 61-certified low-lead fixtures; the plumber should confirm the fixtures meet current lead standards. Consider adding an NSF/ANSI 53-certified drinking water filter at the kitchen tap until the service line is replaced.

humid-continental Understanding the local call pattern helps set realistic expectations for plumber availability and response time during peak periods — during high-demand weeks, advance scheduling is advisable for non-emergency work.

Supply shut-off valve condition, rough-in dimension compatibility with the new fixture, and whether corroded supply lines require replacement are the main drivers. Incompatible rough-in spacing or a seized stop valve that must be cut out increases time and material cost. Valve and supply line condition are assessed before the install scope is set. A verified plumber provides a written estimate covering price, scope, and permit requirements before any work begins.

Yes. Every plumber matched through AlertPlumber holds an active Missouri state contractor license. The Missouri licensing database is checked at each routing — not just at initial signup — so the status reflects current standing, including any recent disciplinary actions, renewals, or insurance lapses. Active Missouri licensure requires documented proof of bonding, liability coverage, and continuing education current as of the routing date.

AlertPlumber does not charge homeowners. The referral fee is paid by the plumber when they accept a qualified call — it is their customer-acquisition cost, not an added charge to you. The plumber provides a written price assessment before any work begins; if the quote doesn't fit your situation, you can decline at any point.